Deck Jak™ Components

Deck Jak® Tile Support

Deck Jak®

The Deck Jak® is the main part of the system which is generally used independently of the other base components.  See more information here

See other Deck Jak® Components that you may require below:

Deck Jak® Spacers

Require extra height on your Deck Jak®?

We have two sizes available – These fit underneath the Deck Jak® tile support. They can be stacked to achieve the required lift and are designed to be used beneath a Deck Jak® tile support, not independently.

20mm Deck Jak® Spacer

The Deck Jak® Spacer clips snugly beneath the Deck Jak® tile support. They are stackable, with each one providing an additional 20mm lift. Drainage ports are included in the design to alleviate water stagnation problems. These are fully integratable with the 50mm Deck Jak® Spacer. The 110mm diameter base provides a very solid platform.

50mm Deck Jak® Spacer

The 50mm Deck Jak® Spacer is Urban Building Product’s recent addition, and has been developed to meet the ever growing demand by customers to evolve the system.The 50mm Deck Jak® Spacer, like the 20mm version, clips snugly beneath the Deck Jak® tile support and is stackable, providing an additional 50mm lift each. The base of this version is comparable to the 20mm.

The photo to the left shows the view from above a Deck Jak® Spacer. Only the flat base comes into contact with the waterproof membrane. All parts in contact have smooth rounded edges. The drainage ports shown allow water to drain from the Deck Jak® Spacer and are similar to the drainage ports in the base of the Deck Jak® tile supports. This eliminates stagnant water smells.

200mm Diameter Deck Jak® Base Plate with additional 2° fall compensation.

This product sits under any Deck Jak® tile support configuration. As well as negating any adverse effects on the ratings of acoustic membranes, the built-in fall compen- sation allows the Deck Jak® tile support system to be used on up to 4° falls. Made from RECYCLED Polycarbonate.
The photo to the left shows a Deck Jak® tile support seated on a combination of 20mm and 50mm Deck Jak® Spacers.

The deck will need to be fully enclosed to ensure there is no chance of any lateral (sideways) movement. This stacking system provides a very stable base for the Deck Jak® tile support, and tiled surface. The 50mm Deck Jak® Spacer allows more stability than ever on high (up to 400mm) support, pedestrian area

Wall Spacer Options

Wall Spacers are used to keep the ’tiled’ surface 6mm or 12mm away from all perimeters and entrance-ways.

This gap allows drainage down the wall / balustrade, eliminates dirt and gunge build-up, the wall spacer is small enough to stop the chance of a high heel slipping through the cracks, especially at entrance-ways.

There are four basic options available.

All types available in bags/sheets of 50.

Wall Plug (or Mushroom)

These are ideal for Timber Panel, compressed sheet and paver use. Measure 50mm in from each end of the side of a ’tile’ against a wall. Drill a 6mm hole 15mm deep, and simply push the Wall Plugs into place.  Made from a polypropylene/ nylon mix. Black only.

Grid Locker

These are ideal for all deck jack tiles, compressed sheet and paver use. The grid lockers lock the whole grid together and provide a water drainage plain. Measure 50mm in from each end of the side of a ‘perimeter tile’ laid against a wall and simply remove the adhesive backing and stick the Grid Locker into place.  These are self adhesive 10mm polyurethane bumpers.

Spacer Disc

These are used to provide a drainage gap between a Stainless Steel or Aluminium angle (not supplied) and the cladding / balustrade. The angle provides a convenient, tidy completion point for the perimeter tiles sitting on the deck jacks. This method is especially useful where a very small piece of tile requires support, although the angle may simply be installed for aesthetic purposes. Screws or angle are not supplied with this system.

Made from a polypropylene/ nylon mix. Black only.

Tile Edge Clip

These are specifically designed for 14mm self supporting deck jack tiles, depending on tile manufacturers nominal tolerances. No drilling or screwing is required with this version of Wall Spacer. The Tile Edge Clip, as the name suggests clips on to the edge of the tiles. These can be placed 50mm in from the corner of all perimeter deck jack tiles, or can be used to bridge a deck jack tile joint. See additional photos below.

Tile Edge Clips are available as standard black. Please ask about custom colours for your tile.


Urban Building Products Ltd
26B Neil Park Drive
East Tamaki
Manukau 2013

Phone: 09 277 7538
Fax: 09 277 7539

Urban Building Products Ltd
P.O.Box 204 312
Manukau 2161